Бих искала да попитам следното:
Когато някой ви даде схема,откъде и как си намирате конци?Ако трябва да се купуват цели чилета,гоблена много се оскъпява. :?
Printable View
Бих искала да попитам следното:
Когато някой ви даде схема,откъде и как си намирате конци?Ако трябва да се купуват цели чилета,гоблена много се оскъпява. :?
Аз например първо проверявам какво имам в наличност. След това отивам и си купувам останалите конци. Ако е малък модел с много цветове скъпичко излиза. Но ако е голям не най-малкото не даваш на куп доста пари.
Аз правя точно като Jovany първо проверявам какво имам в наличност :wink: и чак тогава отивам да купувам :) Случвало ми се е да ми излезе някое малко гобленче доста скъпичко, но пък след това имам в наличност още конци, просто поглеждам нещата от тази страна и готово :idea:
Досега съм шила само готови комплекти с български конци.От руски сайт си изтеглих схема на гоблен с конци DMC.Малък, а с много цветове.Помолих една позната на магазин за гоблени да ми замени някои от цветовете с унгарските PUPPETS/нещо такова беше/ и само цветовете, които са включени в лицето ги оставих непроменени DMC,но наистина ако нямаш запаси в къщи излиза скъпичко.Би било добре да ги продаваха на метър.
Аз точно по тази причина съм се хванал за DMC и само с тях си работя.
Az syshto. Skypichko e, no krajnia rezultat e pone 10 pyti po kachestven.Цитат:
Първоначално написано от Jovany
Вече навсякъде по магазините има и конци Анхор.Какво ви е мнението за тях,те са на цените на ДМЦ.Кои от двата вида предпочитате?Аз съм шила досега с бълг.конци,ДМЦ и Анхор.С унгарски не съм шила и нямам намерение.Всъщност ДМЦ и Анхор най-много ми харесват по същите причини както и на вас,но не мога да определя кой от двата вида да предпочета и да карам с него. :lady:
Аз пък нямам предпочитания в смисъл мога да шия със всичко, качеството на всички конци е добро. Шила съм и със пъпетс и анхор и дмс и любица и българското мулине. Но незнам защо май ми е най-приятно със дмс :wink:
За мен са на кантар като качество. И двете марки са добри. Но съм се спрял на DMC защото по мое мнение повечето безплатни модели са конструирани с тях. :D
Ние българите нали винаги аванта търсим :D
e....nali ima tablica za preobryshtane DMC v Anchor i obratnoto, v nikoj ot sluchaite ne gubim :smokin:
Az predpochitam DMC pred Anchor. Zashto, shte dopisha kato se vyrna v kyshti, veche me e sram vse da pisha na latinica ot rabotata. :D
Да така е но съвпадението не е 100% :smokin:
O, za tova si prav...niama kak da ima syvpadenie 100%.
Благодаря :) Това ,че не съвпадат 100% при преобразуване е фатално само за гоблените където се шият лица.При другите предполагам,че няма чак такъв проблем при разминаването. :lady:
Ми не знам примерно при пейзажите дали има голямо значение но аз гледам да не правя такива комбинации. Ако е с Анхор модела и изкам да го изработя предпочитам да отида и да си купя конци
Много благодаря на всички ви за изчерпателните отговори. :yes:
Аз също си харесах доста гоблени от руските сайтове,обиколих всички магазини,които знам в Пловдив,но никъде не продават на метър.Явно в началото ще трябва да си накупя доста чилета,но за следващи гоблени вече ще имам някои в наличност и така...........
Попитах,защото досега съм шила само готови комплектовки. :lady: