:baby:не мога да разбера откъде, а и как да си изтегля програмката РМ
Printable View
:baby:не мога да разбера откъде, а и как да си изтегля програмката РМ
Здравейте, мога ли да попитам при разпечатване на схемите как да ми излезе сивата зона която застъпва листите?
Благодаря предварително.
Намерих го :) page setup -> Content -> show page overlapping
Здравейте приятели. Някой знае ли дали PM може да се инсталира наОС Android, за да я използвам от таблет
Здравейте,някой знае ли как по снимка се прави гоблен.
Искам да си махна бекстича от схемата,може ли някой да ми каже какво да натисна моляяяяя,че и на всичкото отгоре ми е на руски програмата и пак не виждам кое да натисна:(
Не мога да го обясня с думи,но мога да то покажа два начина.
Лошото е,че има ограничени в приложените картинки,въпреки,че използвам външен източник и ще бъдат няколко поста едно след друго.
http://f16.ifotki.info/thumb/2558119...0172362562.jpg http://f16.ifotki.info/thumb/f414ce4...0172362591.jpg http://f16.ifotki.info/thumb/7774ee7...0172362621.jpg http://f16.ifotki.info/thumb/71ece09...0172362661.jpg
Това е първия начин.Доста е пипкав.
А това е вторият начин(постовете са два,един след друг,за този начин)
http://f16.ifotki.info/thumb/c649748...0172362897.jpg http://f16.ifotki.info/thumb/4d31ecc...0172362926.jpg http://f16.ifotki.info/thumb/63c04eb...0172362953.jpg http://f16.ifotki.info/thumb/7b90500...0172362992.jpg http://f16.ifotki.info/thumb/757918d...0172363015.jpg
А ако схемата е без фон,запълвам празните полета с някакъв контрастен цвят,който не е от палитрата на схемата,изчиствам бековете по втория начин и после изтривам излишния допълнителен цвят.
Дано съм била ясна и полезна.
Лично аз използвам повече втория начин,защото първият ме побърква:uhhhh:
Този втори начин сигурен ли е, че след като се изтрие цвета на бекстича , след това при възстановяване на цвета на празните клетки, ако е имало бодове от различен тип първоначално / кръстат , полукръстат и други в различни посоки / ще се възстановят на точните им места ???
Или този втори начин е подходящ само при един вид бод . Питам защото не съм го пробвала, а ми се струва че ще има проблем ... при по- сложни схеми ...
Последната снимка не работи с увеличение на клика и може и там е отговора на въпросът ми ???
http://f16.ifotki.info/thumb/d2fa14a...0172374335.jpg
Съжалявам за дефектиралото фото.
За по-сложните схеми се използва първият начин.Иначе всичко се разваля.
Аз понеже съм закостенял привърженик на гобленовия бод,ако ми хареса по-сложна схема,си я преработвам в класическа гобленова.Ако стане,де.Гледам виртуалния резултат.Ако се получи мацаница,просто спирам.Търся картината,по която е работен модела и си правя класическа гобленова схема.